Directed Electronics Matrix 1 Przewodnik Instalacji Strona 1

NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other tha

© 2008 Directed Electronics- All rights reserved.10H1/11 RED (+)12V constant power inputBefore connecting this wire, remove the supplied fuse. Connect

© 2008 Directed Electronics- All rights reserved.11Door Lock Harness (H2), 3-PIN ConnectorH2/AH2/BH2/C___Green (-) Lock, (+) Unlock Output___Empty U

© 2008 Directed Electronics- All rights reserved.12Plug-In LED and valet/program switchThe LED and the valet switch are incorporated into the Control

© 2008 Directed Electronics- All rights reserved.13Programmer Interface, 3-Pin BLACK PlugThe BLACK three-pin port connection is for programming the un

© 2008 Directed Electronics- All rights reserved.14Important! To achieve the best possible range, DO NOT leave the control center cable bundled

© 2008 Directed Electronics- All rights reserved.15Optional Sensor Harness, 4-pin ConnectorThe four-pin sensor harness is optional, and is not include

© 2008 Directed Electronics- All rights reserved.16Programming JumperLight Flash JumperThis jumper is used to determine the light flash output. In the

© 2008 Directed Electronics- All rights reserved.17Bypassing Sensor InputsThere are times when you need to temporarily bypass all sensor in

© 2008 Directed Electronics- All rights reserved.18System Features Learn RoutineThe System Features Learn Routine dictates how the unit operates.

© 2008 Directed Electronics- All rights reserved.194. Select a Feature. Press and release the Valet/Program switch the number of times corresponding

Bitwriter™, Code Hopping™, DEI®, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nite-Lite®, False Alarm Control Technology™, Rev

© 2008 Directed Electronics- All rights reserved.20To access another feature in the same menu:Press and release the Valet/Program switch the number of

© 2008 Directed Electronics- All rights reserved.21System Features MenusMenu #1 - Basic FeaturesItems in bold text have been programmed to the default

© 2008 Directed Electronics- All rights reserved.22Menu #2 - Advanced Features Feature One Chirp Two-Chirp Number Setting Setting 2-

© 2008 Directed Electronics- All rights reserved.231-3 IGNITION CONTROLLED DOOR LOCKS ON/OFF: When turned on, the doors will lock three seconds after

© 2008 Directed Electronics- All rights reserved.241-8 AUTOMATIC ENGINE DISABLE (AED) ON/OFF: AED is a full-time, passive starter disable tha

© 2008 Directed Electronics- All rights reserved.252-3 FALSE ALARM CONTROL TECHNOLOGY (FACT II™) ON/OFF: FACT II stops repeated triggering of th

© 2008 Directed Electronics- All rights reserved.262-8 DOUBLE PULSE UNLOCK ON/OFF: Some vehicles require two pulses on a single wire to unlock th

© 2008 Directed Electronics- All rights reserved.27Transmitter/Receiver Learn RoutineThe system comes with two transmitters that have been ta

© 2008 Directed Electronics- All rights reserved.28 Channel Number Function Wire Color 1 Arm/Disarm 2 Panic only 3 Silent Mode/Remote Valet

© 2008 Directed Electronics- All rights reserved.295. Release. Once the code is learned, the Valet/Program button can be released. To exit the learn

© 2008 Directed Electronics- All rights reserved.3ContentsPrimary Harness (H1) Wire Connection Guide ...

© 2008 Directed Electronics- All rights reserved.30Transmitter ConfigurationsThe transmitters can be programmed with the standard or three-bu

© 2008 Directed Electronics- All rights reserved.31DiagnosticsThe system’s microprocessor monitors and reports all active and violated zones when armi

© 2008 Directed Electronics- All rights reserved.32Table of Zones Zone No. Trigger type Input description 1 Instant H1/6 BLUE - Connect to option

© 2008 Directed Electronics- All rights reserved.334. Press and release the Valet/Program switch within 5 seconds. The LED will flash in groups indic

© 2008 Directed Electronics- All rights reserved.34Optional Vehicle Recovery System (VRS)VRS is an optional feature designed to disable a vehicl

© 2008 Directed Electronics- All rights reserved.35TroubleshootingStarter kill doesn’t work. Is the correct starter wire being interrupted? If

© 2008 Directed Electronics- All rights reserved.36System will not passively arm until it is remotely armed and then disarmed. Are the door

© 2008 Directed Electronics- All rights reserved.37Blue 2 pin plug, valet switch plug from 6111T 6111T control centerWhite 2 pin LED plug from 6111T

© 2008 Directed Electronics- All rights reserved.4Primary Harness (H1) Wire Connection GuidePrimary Harness Wiring DiagramH1/1H1/2H1/3H1/4H1/5H1/6H1/7

N3105X 2008-12Vista, CA 92081www.directed.com© 2008 Directed Electronics.—All rights reserved.

© 2008 Directed Electronics- All rights reserved.5IMPORTANT! Never interrupt any wire other than the starter wire.H1/2 WHITE (+/-) light flash outputA

© 2008 Directed Electronics- All rights reserved.6H1/3 WHITE/BLUE 200 mA (-) channel 3 outputThis wire provides a (-) 200 mA output whenever the tra

© 2008 Directed Electronics- All rights reserved.7IMPORTANT! Never use this wire to drive anything but a relay or a low-current input! T

© 2008 Directed Electronics- All rights reserved.8H1/6 BLUE (-) instant trigger inputThis input will respond to a negative input with an instant trigg

© 2008 Directed Electronics- All rights reserved.9grounded at the same location.H1/9 YELLOW (+) ignition inputConnect this wire to the (+) 12 volts ig