Directed Electronics 581XP Przewodnik Instalacji

© 2003 Directed Electronics, Inc. Vista, CA N542P 6-03NOTE: This product is intended for installation by a professional installer only!Any attempt to

10 © 2003 Directed Electronics, Inc. Vista, CAwiring diagramsThe primary harness supplied with this unit is the standard 12-pin harness used by Direct

© 2003 Directed Electronics, Inc. Vista, CA 11__________________________________________________________________________________________PINK/WHITE (+)

12 © 2003 Directed Electronics, Inc. Vista, CA________________________________________________________________________________________________PINK (-)

© 2003 Directed Electronics, Inc. Vista, CA 13primary harness (H1) wire connection guideThis wire supplies a (-)500 mA ground as long as the system is

14 © 2003 Directed Electronics, Inc. Vista, CAThis input comes from the factory set to 2 activation pulses. This means that it is necessary to have 2

© 2003 Directed Electronics, Inc. Vista, CA 15within 15 seconds after unlocking the driver's door. The BLUE wire outputs a low current (-) pulse

16 © 2003 Directed Electronics, Inc. Vista, CABefore connecting this wire, remove the supplied fuse. Connect to the battery positive terminal or the c

© 2003 Directed Electronics, Inc. Vista, CA 17relay key switch interface wire connection guideAll except the red heavy gauge wires leading from the re

18 © 2003 Directed Electronics, Inc. Vista, CAauxiliary harness (H2) wire connectionguideThis wire provides 200 mA programmable output. (See Feature D

© 2003 Directed Electronics, Inc. Vista, CA 19This wire sends a negative pulse every time the remote start is activated or the doors are unlocked. Thi

2 © 2003 Directed Electronics, Inc. Vista, CAtable of contentsBitwriter™, Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, LearnRoutine™,

20 © 2003 Directed Electronics, Inc. Vista, CAremote start harness (H3) wire connection guideThis wire supplies a 200mA output as soon as the module b

© 2003 Directed Electronics, Inc. Vista, CA 21Figure A Figure BIMPORTANT! Always perform the Vehicle Safety Check section of this guide to verify that

22 © 2003 Directed Electronics, Inc. Vista, CA1. Make sure there is adequate clearance to the front and rear of the vehicle because it may move slight

© 2003 Directed Electronics, Inc. Vista, CA 23Diagram A - General Motors trucks, sport utility vehicles and column shifting passenger vehicles:Diagram

24 © 2003 Directed Electronics, Inc. Vista, CA1995 and newer vehicle anti-theft systems(immobilizers) 1995 and newer vehicle anti-theft systems (immob

© 2003 Directed Electronics, Inc. Vista, CA 25transponder will then send a unique code back to the transceiver for evaluation. If the code matches a v

26 © 2003 Directed Electronics, Inc. Vista, CAplug-in LED and valet/program switchThese plug into the module. The status LED plugs into the small two-

© 2003 Directed Electronics, Inc. Vista, CA 27programming jumpersThis jumper is used to determine the light flash output polarity. In the (+) position

28 © 2003 Directed Electronics, Inc. Vista, CAtransmitter/receiver learn routineThe system comes with transmitters that have been taught to the receiv

© 2003 Directed Electronics, Inc. Vista, CA 293. Transmit. While HOLDING the Valet/Program switch, press the button on the transmitterthat you would l

© 2003 Directed Electronics, Inc. Vista, CA 3warning! safety firstThe following safety warnings must be observed at all times: Due to the complexity

30 © 2003 Directed Electronics, Inc. Vista, CAtransmitter configurationsThe transmitters can be programmed with the separate or single button arm/disa

© 2003 Directed Electronics, Inc. Vista, CA 31remote control diagram

32 © 2003 Directed Electronics, Inc. Vista, CAstandard mode configuration1. Auxiliary Channel Out2. Receive Indicator3. Signal Indicator4. Transmit In

© 2003 Directed Electronics, Inc. Vista, CA 33operating settings learn routineThe System Features Learn Routine™ dictates how the unit operates. Due t

34 © 2003 Directed Electronics, Inc. Vista, CAnecessary to get from the feature you just programmed to the feature you wish to access. For example, in

© 2003 Directed Electronics, Inc. Vista, CA 35feature menusFactory default settings are indicated in bold in the following feature tables.FEATURE DEF

36 © 2003 Directed Electronics, Inc. Vista, CAFEATURE DEFAULT - LED ON SETTING LED OFF SETTINGNUMBER (PRESS CHANNEL 1) (PRESS CHANNEL 2)2-1 Engine ch

© 2003 Directed Electronics, Inc. Vista, CA 37feature descriptionsThe features of the system are described below. Features that have additional settin

38 © 2003 Directed Electronics, Inc. Vista, CA1-9 CHANNEL 2: In the delayed validity default setting the Channel 2 output will output a negative (-)

© 2003 Directed Electronics, Inc. Vista, CA 392-1 ENGINE CHECK ON/OFF: In the default setting the remote start will monitor either the vehicle's

4 © 2003 Directed Electronics, Inc. Vista, CAinstallation points to rememberIMPORTANT! This product is designed for fuel-injected, automatic transmis

40 © 2003 Directed Electronics, Inc. Vista, CA2-9 2ndIGNITION/ACCESSORY OUTPUT: This will allow the PINK/WHITE to be used as a 2ndignition or anaccess

© 2003 Directed Electronics, Inc. Vista, CA 41shutdown diagnosticsThe unit has the ability to report the cause of the last shutdown of the remote star

42 © 2003 Directed Electronics, Inc. Vista, CArapid resume logicThe Rapid Resume Logic feature ensures that when the security system is powered back u

© 2003 Directed Electronics, Inc. Vista, CA 43valet modeTo enter or exit Valet® Mode with the Valet®/Program switch:1. Turn the ignition on and then o

44 © 2003 Directed Electronics, Inc. Vista, CAf. Activate the remote start system. If the starter engages, immediately step on the brake to shut dow

© 2003 Directed Electronics, Inc. Vista, CA 45lite. Also make sure that the ground wire is going to a chassis ground and not to something under the da

46 © 2003 Directed Electronics, Inc. Vista, CAwiring quick reference guide

© 2003 Directed Electronics, Inc. Vista, CA 47relay satellite wiring quick reference guide

© 2003 Directed Electronics, Inc. Vista, CA 5 Keep the control module away from the heater core (or any other heat sources) and any obvious leaks. T

6 © 2003 Directed Electronics, Inc. Vista, CAIf the optional starter kill relay or its connections are immediately visible upon removal of the under-d

© 2003 Directed Electronics, Inc. Vista, CA 7The ignition wire is powered when the key is in the run or start position. This is because the ignition w

8 © 2003 Directed Electronics, Inc. Vista, CAHow to find the starter wire with your multimeter:1. Set to DCV or DC voltage (12V or 20V is fine).2. Att

© 2003 Directed Electronics, Inc. Vista, CA 9To test for a tachometer wire, a multimeter capable of testing AC voltage must be used. The tachometer wi